In the construction of wall painting, the selection of paint is the primary task and an important factor that affects the entire construction process. However, in the process of selecting paints, consumers often have the following misunderstandings. Today, Xiao Bian has carefully selected four misunderstandings for you to choose from. Let you be a savvy consumer.
Myth # 1: Anti-crack paint must be resistant to cracks. Regardless of new homes, the phenomenon of wall cracking is very high. Many people are struggling to choose a good paint to solve the problem of cracking. Once there was a brand-name paint package that was shockingly written "Cracking Resistance". Many consumers think that as long as these paints are used, they can prevent cracking on the walls. In fact, this is not very useful.
Xiao Bian Weapon: A thin layer of paint film can actually prevent the occurrence of wall cracking, which is unlikely. The "elastic latex paint" currently on the market can generally only compensate for micro-cracks below 0.3 mm. If the wall is cracked, to solve these problems, it is best to use latex paint to make up, or use cement to make up the cracks, and then paint.
Myth #2: Blindly worrying about the environmental protection of paints As people pay more and more attention to health, many people are not afraid of counterfeits but are afraid of decoration pollution. When it comes to renovation pollution, many people immediately think of paint. Everyone thinks that paints contain a lot of toxic substances such as formaldehyde, benzene, and VOCs. Therefore, when choosing coatings, they are also very worried. But in fact, this concern is not necessary. Now that the safety of many coatings has reached a good level, consumers do not have to worry too much.
Xiao Bian Weapons: In fact, many consumers worry about the environmental protection of paint can be said to be blind. Now most of the qualified interior wall coatings are safe, they are generally water-based coatings, environmental protection waterborne coatings produce less harmful substances such as formaldehyde, benzene, etc., generally have little harm to the human body, as long as they pay attention to indoor ventilation after renovation, Can effectively avoid these decoration pollution.
Myth #3: Brands that care too much about paint Many homeowners think that buying paints is good for buying well-known brands. Of course, well-known brands have certain quality guarantees, but they can't blindly pursue brands. In fact, the quality and effectiveness of many ordinary brand products and well-known brand products are not much different, but there is a gap in prices. Reasonable choice of paint is the wise choice.
Xiao Bian Weapons: When selecting paints, we should first understand the quality, reputation and market conditions of various brands of paints on the Internet or other channels. With the same effect of paint, try to choose a more reasonable price brands.
Misunderstanding 4: Buying materials is good Many owners are afraid to buy less paint. Therefore, they are purchased in bulk at the very beginning. In fact, this is a mistake. This has resulted in the waste of materials, thus affecting the cost of construction and the accumulation of construction sites. Excessive coating also has a certain impact on construction safety.
Xiao Bian Weapons: Before construction, we must look at the area of â€‹â€‹the construction area to estimate the amount of purchased materials, usually purchased materials should be 10% -15% more than the budget, so you can reduce the chance of repurchasing materials, and waste Opportunities can also be minimized.
Blind Flanges, Weld neck flanges, Socket flanges, Slip On Flanges, WN Flanges,
Steel Flange: 20#, Q235, A105, ST20, C22.8, Rst37.2,
Size: 15A- 2000A, 1/2"-78"
Treatment of Steel flanges: Anti-rust
Oil, Transparent/ Yellow/Black Anti-rust Paint, Zinc, Hot dipped Galvanized.
A Steel flange is an external
or internal ridge, for strength, as the flange of an iron beam such as an
I-beam or aT-beam; or for attachment to another object, as the flange on the
end of a pipe, steam cylinder, etc., or on the lens mount of a camera; or for a
flange of a rail car or tram wheel. Thus flanged wheels are wheels with a
flange on one side to keep the wheels from running off the rails. The term
"flange" is also used for a kind of tool used to form flanges. Pipes
with Steel flanges can be assembled
and disassembled easily.
A Blind flange is
round plate which has all of the relevant both holes but no center hole, and
because of this feature this flange is used to close off the ends of a piping
systems and pressure vessel openings. It also permits easy access to the
interior of a line or vessel once it has been sealed and must be reopened.
We have adopted
advanced production equipment and technologies to manufacture our blind flanges weld neck socket flanges slip on flanges and threaded flanges,
which can not only improve product quality, but also save raw materials. Our
products have high strength, good toughness and resistance to corrosion.
Carbon Steel Flanges
Slip On Flanges,WN Flanges,Welding Neck Flange,Blind Flanges
Cangzhou Fixed Star Steel Co.,Ltd , http://www.fixedstarpipe.com